What it means is that we can
stack graphene strips vertically on a diamond substrate and presumably engineer
the properties of their surfaces. It
sounds like a fabulous memory storage device.
It also appears to be feasible
and Moore Moore
Graphene is continuing its
astounding emergence in the labs and will soon be in everything. What is most remarkable is how little the
mainstream media has taken notice.
Rice, Hong Kong Polytechnic physicists
calculate 100 trillion graphene field effect transistors could fit on a chip
SEPTEMBER 27, 2011
To stand a ribbon of graphene upright, it needs diamond on the
soles of its shoes. A new paper by collaborators at Rice University
and Hong Kong Polytechnic University demonstrates the possibility that tiny
strips of graphene -- one-atom-thick sheets of carbon -- can stand tall on a
substrate with a little support. This leads to the possibility that arrays of
graphene walls could become ultrahigh density components of electronic or
spintronic devices.
Calculations by Rice theoretical physicist Boris Yakobson, Assistant
Professor Feng Ding of Hong Kong Polytechnic
and their collaborators showed substrates not only of diamond but also nickel
could chemically bind the edge of a strip of a graphene nanoribbon. Because the
contact is so slight, the graphene walls retain nearly all of their inherent
electrical or magnetic properties.
We propose integrating graphene nanoribbons (GNRs) onto a substrate in
an upright position whereby they are chemically bound to the substrate at the
basal edge. Extensive ab initio calculations show that both nickel (Ni)- and
diamond-supported upright GNRs are feasible for synthesis and are mechanically
robust. Moreover, the substrate-supported GNRs display electronic and magnetic
properties nearly the same as those of free-standing GNRs. Due to the extremely
small footprint of an upright GNR on a substrate, standing GNRs are ideal
building blocks for synthesis of subnanometer electronic or spintronic devices.
Theoretically, standing GNR-based microchips with field-effect transistor (FET)
densities up to 10^13 per cm2 are achievable.
Yakobson and Ding calculated a theoretical potential of putting 100
trillion graphene wall field-effect transistors (FETs) on a square-centimeter
chip.
That potential alone may make it possible to blow past the limits implied by Moore's Law -- something Yakobson once discussed with Intel founder Gordon Moore himself.
"We met in Montreal, when nano was a new kid on the block, and had a good conversation," said Yakobson, Rice's Karl F. Hasselmann Chair in Engineering and a professor of materials science and mechanical engineering and of chemistry. "
"This kind of strategy may help sustain
A sheet of material a fraction of a nanometer wide is pretty pliable, he said, but the laws of physics are on its side. Binding energies between carbon in the diamond matrix and carbon in graphene are maximized at the edge, and the molecules bind strongly at a 90-degree angle. Minimal energy is required for the graphene to stand upright, which is its preferred state. (Walls on a nickel substrate would be angled at about 30 degrees, the researchers found.)
Yakobson said the walls could be as close to each other as 7/10ths of a nanometer, which would maintain the independent electronic properties of individual nanoribbons. They could potentially be grown on silicon, silicon dioxide, aluminum oxide or silicon carbide.
The research illustrated differences between walls made of two distinct types of graphene, zigzag and armchair, so-called because of the way their edges are shaped.
Sheets of graphene are considered semimetals that have limited use in electronics because electrical current shoots straight through without resistance. However, armchair nanoribbons can become semiconductors; the thinner the ribbon, the larger the band gap, which is essential for transistors.
Zigzag nanoribbons are magnetic. Electrons at their opposing edges spin in opposite directions, a characteristic that can be controlled by an electric current; this makes them suitable for spintronic devices.
In both cases, the electronic properties of the walls can be tuned by changing their height.
The researchers also suggested nanowalls could become nanoarches by attaching opposing ends of a graphene ribbon to the substrate. Rather than lie flat on the diamond or nickel surface, the energies at play along the binding edges would naturally force the graphene strip to rise in the middle. It would essentially become a half-nanotube with its own set of potentially useful properties.
Precisely how to turn these two-dimensional building blocks into a three-dimensional device presents challenges, but the payoff is great, Yakobson said. He noted that the research lays the groundwork for subnanometer electronic technology.
Editor’s note: A link to a high-resolution image for this story is
available at the end of the news release.
Mike Williams
Graphene walls could make powerful electronics
Rice,
To stand a ribbon of graphene upright, it needs diamond on the soles of
its shoes.
A new paper by collaborators at Rice University and Hong Kong
Polytechnic University demonstrates the possibility that tiny strips of
graphene -- one-atom-thick sheets of carbon -- can stand tall on a substrate
with a little support. This leads to the possibility that arrays of graphene
walls could become ultrahigh density components of electronic or spintronic devices.
The work was published this month in the online edition of the Journal of the American
Chemical Society.
Calculations by Rice theoretical physicist Boris Yakobson, Assistant
Professor Feng Ding of Hong Kong Polytechnic
and their collaborators showed substrates not only of diamond but also nickel
could chemically bind the edge of a strip of a graphene
nanoribbon. Because the contact is so slight, the graphene walls retain
nearly all of their inherent electrical or magnetic properties.
And because they're so thin, Yakobson and Ding calculated a theoretical
potential of putting 100 trillion graphene wall field-effect transistors (FETs)
on a square-centimeter chip.
That potential alone may make it possible to blow past the limits
implied by Moore's Law --
something Yakobson once discussed with Intel founder Gordon Moore himself.
"We met in Montreal, when nano was a new kid on the block, and had
a good conversation," said Yakobson, Rice's Karl F. Hasselmann Chair in
Engineering and a professor of materials science and mechanical engineering and
of chemistry. "Moore Texas
to skyscraper condos in Hong Kong .
"This kind of strategy may help sustain Moore
A sheet of material a fraction of a nanometer wide is pretty pliable,
he said, but the laws of physics are on its side. Binding energies between
carbon in the diamond matrix and carbon in graphene are maximized at the edge,
and the molecules bind strongly at a 90-degree angle. Minimal energy is
required for the graphene to stand upright, which is its preferred state.
(Walls on a nickel substrate would be angled at about 30 degrees, the
researchers found.)
Yakobson said the walls could be as close to each other as 7/10ths of a
nanometer, which would maintain the independent electronic properties of
individual nanoribbons. They could potentially be grown on silicon, silicon
dioxide, aluminum oxide or silicon carbide.
The research illustrated differences between walls made of two distinct
types of graphene, zigzag and armchair, so-called because of the way their
edges are shaped.
Sheets of graphene are considered semimetals that have limited use in
electronics because electrical current shoots straight through without
resistance. However, armchair nanoribbons can become semiconductors; the
thinner the ribbon, the larger the band gap, which is essential for
transistors.
Zigzag nanoribbons are magnetic. Electrons at their opposing edges spin
in opposite directions, a characteristic that can be controlled by an electric
current; this makes them suitable for spintronic devices.
In both cases, the electronic properties of the walls can be tuned by
changing their height.
The researchers also suggested nanowalls could become nanoarches by
attaching opposing ends of a graphene ribbon to the substrate. Rather than lie
flat on the diamond or nickel surface, the energies at play along the binding
edges would naturally force the graphene strip to rise in the middle. It would
essentially become a half-nanotube with its own set of potentially useful
properties.
Precisely how to turn these two-dimensional building blocks into a
three-dimensional device presents challenges, but the payoff is great, Yakobson
said. He noted that the research lays the groundwork for subnanometer
electronic technology.
Co-authors of the paper are Qinghong Yuan, Hong Hu and Junfeng Gao of
the Institute of Textiles and Clothing, Hong Kong
Polytechnic University ,
and Zhifeng Liu of the Chinese University of Hong Kong .
Ding was a research scientist in Yakobson's Rice lab from 2005 to 2009 and has
a complimentary appointment at Rice.
No comments:
Post a Comment